Learn How To Repair A Tire Puncture Are Better life?

Spread the love

As a driver, it’s important to know how to perform basic maintenance on your vehicle. One common issue that can arise is a tire puncture. While this may seem like a daunting task, it’s actually quite easy to repair a tire puncture.

In this blog post, we’ll walk you through the steps necessary to fix How To Repair A Tire puncture. By taking the time to learn this simple repair, you can save yourself time and money down the road.

Life Savior Tips- How to Repair a Tire

When Is A Tire Repairable?

First, you have to find out if the tire is repairable or not. According to USTMA (U. S. Tire Manufacturers’ Association), the inner and outer tread of a tire is not repairable. If it has a tear in the middle part, only then it is repairable. When the puncture is in the sidewall or shoulder, it is recommended to replace the tire to avoid accidents.

Also, any overlapping or across-the-line gouge should be avoided. Depending on the amount of damage, it should be repaired or replaced.

Tools To Repair Tire

Once you’ve found the tire repairable, you’ll need only a handful of tools to mend it. You need to store them in the car so that you can use them whenever needed.

  • Tire plug kit,
  • Inflator,
  • Tire wrench,
  • Jack stands,
  • Cutter,
  • Chalk or marker,
  • Commercial tire sealant, &
  • Pliers.

How To Repair A Tire In The Easiest Way

Fixing a flat tire is easier than you might think. Here are the steps and the tools you will need.

  1. Locate a jack under the car to lift the vehicle.
  2. Remove the hubcap.
  3. Remove the valve stem cap.
  4. Remove the tire.
  5. Locate the tire valve’s stem.
  6. Pour some air into the tire.
  7. Insert the tire valve’s stem into the tire.
  8. Install the tire valve’s stem.
  9. Place the hubcap back on.

The tire patching can be done with the following easy steps.

How to Repair a Tire

Inflate The Tire & Find Any Leak.

When something breaks through the tire, there is a chance of losing air pressure and the tire becomes flat. At this point look for two things- air leakage, and protruding object. If your tire became flat because of air leakage, you need to inflate it first with an inflator. Then find any leaks caused by the nail or screw.

Look for the cuts and holes causing the air leak. You may get a hissing noise and you can also check with a hand running over it. Point to be noted; when there is a leak and the tire is flat, you’re about to use a sealant, then inflate the tire in the first place. Otherwise, when there is a screw stuck in the tire, you have to inflate it after filling the hole with tire plug kits.

Fix The Leak With Tire Sealant.

According to the directions on the sealant can apply it to the inflated tire. Drive the car front and backward to evenly distribute the liquid. Remember you need to replace the tire as soon as you can.

Jack Up The Car And Remove Lugs And Wheel.

Now that you’ve found the leak, let’s get to mending it. In this step, loose the lug nuts with a tire wrench or lug wrench. Then jack up the car using a jack stand until the wheel is level with the ground and it is no more burdened with the car’s weight.

You should do it on a sturdy level surface. Use the service manual to get the exact jacking point. Then remove the lugs from the point. Lastly, pull the tire off of the wheelbase.

Remove The Screw And Clean The Hole.

Now if there is an object sticking out of the tire, remove it using a plier. Mark the spot using chalk or marker, as it will be easier to work this way. From the tire plug kit, take the rasp tool. Now, push in and pull off the tool in the hole so that it becomes clean for further work.

Thread Plug Through The Hole.

From the kits, take the plug and insert it through the eye of the insertion tool. If you find it difficult to thread it through the tool, squeeze one edge of the plug to the size of the hole.

As you’ve got the plug threaded into the insertion tool, now nicely coat it with rubber cement. For a greater effect, put a dab of cement into the hole before inserting the plug as well. Use a little force to jab the plug into the hole and pull out the tool. Now let the cement dry until the tackiness is gone.

Tire punctures can occur for any reason due to running conditions. So we need strong and good tires. We use many types of tires in cars. I have discussed some tires to help you. What does grand touring tire mean? Types of Turing Ann tires are available. Let’s try to find out which tire is better

Re-Install The Tire And Lugnuts.

After it has dried cut off the extra plug popping out from the hole.  Now fill the wheel with air with an air inflator at the recommended pressure. Make sure no air is coming out.

Splitz some water on the spot and it will show if there is a leak. At this point, re-install the tire and the lug nuts before lowering the vehicle on the jack stand. Then remove the jack stand and tighten the lugs using a lug wrench. And you’re ready to move.

Step One: A plug is more durable compared to sealants. It can back you up to 20,000 miles, where you can ride only at a speed of 50 mph with sealants. But we recommend replacing the plugged tire before the mileage ends.

Step Two: f you think you can’t do this yourself, ask for help from a professional. Also, if you don’t have an inflator, do not remove whatever object has got into the tire until you reach the workshop. As the air will escape and the tire will lose pressure, resulting in a flat tire.

Final Thought

We Hope this article was helpful to solve your Flat Tire repair problem. Again, if you don’t know how to repair a tire puncture, don’t bother yourself doing this. Otherwise, you may have to replace it with a new one. Call a tow truck and ask for professional assistance. You know, help is just a call away. Have a safe ride!

4.4/5 - (11 votes)

Spread the love

Leave a Reply

Your email address will not be published. Required fields are marked *